smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-8-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721010CLA330
Serial Number: JP2940N10ATA1V
LU WWN Device Id: 5 000cca 39cc4e705
Firmware Version: JP4OA3MA
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Nov 3 21:50:08 2018 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9812) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 164) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 098 098 016 Pre-fail Always - 327680
2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 97
3 Spin_Up_Time 0x0007 124 124 024 Pre-fail Always - 300 (Average 309)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1453
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 69
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 140 140 020 Pre-fail Offline - 30
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 33850
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1443
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 2071
193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 2071
194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 19/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 98
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 6986 hours (291 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 20 a0 f8 b4 07 Error: UNC at LBA = 0x07b4f8a0 = 129300640
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 60 60 56 b4 40 08 36d+23:08:48.943 READ FPDMA QUEUED
60 20 58 40 70 b4 40 08 36d+23:08:48.942 READ FPDMA QUEUED
60 20 50 d0 70 b4 40 08 36d+23:08:48.942 READ FPDMA QUEUED
60 10 48 30 71 b4 40 08 36d+23:08:48.942 READ FPDMA QUEUED
60 10 40 68 71 b4 40 08 36d+23:08:48.941 READ FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 6986 hours (291 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 20 60 56 b4 07 Error: UNC at LBA = 0x07b45660 = 129259104
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 58 80 f8 b4 40 08 36d+23:08:27.697 READ FPDMA QUEUED
60 20 50 90 f7 b4 40 08 36d+23:08:27.696 READ FPDMA QUEUED
60 20 48 40 d7 b4 40 08 36d+23:08:27.696 READ FPDMA QUEUED
60 20 40 70 d5 b4 40 08 36d+23:08:27.696 READ FPDMA QUEUED
60 20 38 b0 d4 b4 40 08 36d+23:08:27.695 READ FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 4733 hours (197 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3f 01 cb ec 0a Error: UNC at LBA = 0x0aeccb01 = 183290625
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 28 58 c0 c3 ec 40 08 10d+16:04:49.462 READ FPDMA QUEUED
60 20 50 40 c4 ec 40 08 10d+16:04:49.461 READ FPDMA QUEUED
60 20 48 f0 26 ed 40 08 10d+16:04:49.461 READ FPDMA QUEUED
60 18 40 18 0c ed 40 08 10d+16:04:49.460 READ FPDMA QUEUED
60 20 38 f8 0b ed 40 08 10d+16:04:49.460 READ FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 3784 hours (157 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 f0 f6 3e 0e Error: UNC at LBA = 0x0e3ef6f0 = 239007472
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 40 18 78 f8 3e 40 08 18d+01:18:52.833 READ FPDMA QUEUED
60 40 10 f0 f6 3e 40 08 18d+01:18:52.833 READ FPDMA QUEUED
60 08 00 48 ad 72 40 08 18d+01:18:52.832 READ FPDMA QUEUED
60 18 78 10 ad 72 40 08 18d+01:18:52.620 READ FPDMA QUEUED
60 20 70 08 f0 da 40 08 18d+01:18:52.620 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 17189 -
# 2 Short offline Completed without error 00% 17187 -
# 3 Short offline Completed without error 00% 17103 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.