# smartctl -a /dev/sdb
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.2.0-4-486] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar C4K60
Device Model: HTC426030G5CE00
Serial Number: L57X7Y
Firmware Version: 00P9A0A6
User Capacity: 30 005 821 440 bytes [30,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Oct 21 00:28:47 2017 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 1650) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 28) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000d 100 100 050 Pre-fail Offline - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0006 100 100 000 Old_age Always - 0
4 Start_Stop_Count 0x0032 069 069 000 Old_age Always - 31877
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 7
7 Seek_Error_Rate 0x000f 100 100 050 Pre-fail Always - 954
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Minutes 0x0032 077 077 000 Old_age Always - 11616h+43m (2328)
10 Spin_Retry_Count 0x0013 100 100 050 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 069 069 000 Old_age Always - 31807
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12
193 Load_Cycle_Count 0x0032 040 040 000 Old_age Always - 363168/363181
194 Temperature_Celsius 0x0022 100 076 000 Old_age Always - 31 (Min/Max 8/48)
195 Hardware_ECC_Recovered 0x001a 100 095 000 Old_age Always - 11
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 7
197 Current_Pending_Sector 0x0032 100 099 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 199
200 Multi_Zone_Error_Rate 0x0013 100 100 050 Pre-fail Always - 0
201 Soft_Read_Error_Rate 0x0012 100 100 000 Old_age Always - 0
223 Load_Retry_Count 0x0012 100 100 000 Old_age Always - 0
230 Head_Amplitude 0x0032 097 097 000 Old_age Always - 6966437045920
250 Read_Error_Retry_Rate 0x000a 100 100 000 Old_age Always - 488
SMART Error Log Version: 1
ATA Error Count: 144 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 144 occurred at disk power-on lifetime: 11614 hours (483 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 07 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000007 = 7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 00:00:47.360 READ DMA
ec 00 00 00 00 00 a0 02 00:00:47.350 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:00:47.350 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 00:00:47.340 IDENTIFY DEVICE
00 00 08 00 00 00 a0 06 00:00:47.190 NOP [Abort queued commands]
Error 143 occurred at disk power-on lifetime: 11614 hours (483 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 07 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000007 = 7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 00:00:47.040 READ DMA
ec 00 00 00 00 00 a0 02 00:00:46.510 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:00:46.510 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 00:00:46.500 IDENTIFY DEVICE
00 00 35 0b d6 38 a0 06 00:00:46.350 NOP [Abort queued commands]
Error 142 occurred at disk power-on lifetime: 11612 hours (483 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 07 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000007 = 7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 00:00:47.320 READ DMA
ec 00 00 00 00 00 a0 02 00:00:47.310 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:00:47.310 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 00:00:47.300 IDENTIFY DEVICE
00 00 08 00 00 00 a0 06 00:00:47.150 NOP [Abort queued commands]
Error 141 occurred at disk power-on lifetime: 11612 hours (483 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 07 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000007 = 7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 00:00:46.980 READ DMA
ec 00 00 00 00 00 a0 02 00:00:46.480 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:00:46.480 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 00:00:46.470 IDENTIFY DEVICE
00 00 35 0b d6 38 a0 06 00:00:46.320 NOP [Abort queued commands]
Error 140 occurred at disk power-on lifetime: 11611 hours (483 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 07 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000007 = 7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 00:37:18.190 READ DMA
ec 00 00 00 00 00 a0 02 00:37:18.180 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:37:18.180 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 02 00:37:18.170 IDENTIFY DEVICE
00 00 08 00 00 00 a0 06 00:37:18.020 NOP [Abort queued commands]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.